Audiovox APS-255 Instalační manuál stáhnout pdf

128-5730B

1 of 7

Model APS-255

Installation Manual

Note : When both Passive Arming and Voltage Sensing are selected, you must hardwire the driver’s door pin switch

in order to begin the passive arming sequence.

RF Programmable Features :

Feature Selection 1 Chirp 2 Chirps 3 Chirps 4 Chirps Default

1st Door L/UL 1 Sec. 3.5 Sec. 1 Sec L, Dbl. U/L 1 Sec.

2nd Accy Lock Auto Lock On Auto Lock Off Auto Lock Off

3rd Accy. UL Auto UL Dr. Auto UL All Auto UL Off Auto UL Off

4th Passive Locks Passive Active Active

5th Passive/Active Arm Passive Arm Active Arm Active Arm

6th Voltage Sense Voltage Sense Hardwire Hardwire

7th Siren/Horn Siren/Horn Siren Only Horn Only Siren/Horn

8th Horn Chirp 10mS 16mS 30mS 16mS

9th Override Method Custom Code Valet Valet

10th Two Step Unlock On Off Off

11th Chirp Delete From Tx On Off Off

To program these selectable features;

Action System Response

Turn ignition on No response

Press and release the valet switch 3 times 1 Chirp - LED 1 flash

Within 3 seconds, turn ignition Off Short chirp, then long chirp

First Then On 1 chirp = 1 second door locks

Press transmitter Lock button to change 2 chirps = 3.5 second door locks

Press transmitter Lock button to change 3 chirps = 1 sec. lock, dbl 1 sec. unlock

Second Press and release the valet switch 2 chirps = auto locks off

Press transmitter Lock button to change 1 chirp = auto locks on

Third Press and release the valet switch 3 chirps = auto unlock off

Press transmitter Lock button to change 2 chirps = auto unlock all doors

1 chirp = auto unlock driver's door

Fourth Press and release the valet switch 2 chirps = active locks

Press transmitter Lock button to change 1 chirp = passive locks

Fifth Press and release the valet switch 2 chirps = active arming

Press transmitter Lock button to change 1 chirp = passive arming

Sixth Press and release the valet switch 2 chirps = hardwire

Press transmitter Lock button to change 1 chirp = voltage sense

Seventh Press and release the valet switch 1 chirp = siren and horn output

Press transmitter Lock button to change 2 chirps = siren output only

Press transmitter lock button to change 3 chirps = horn output only

Released 4-5-00.

Rev. B : 4-24-01. - Add chirps to third feature.

SELECTABLE FEATURES

1 2 3 4 5 6 7

Model APS-255 1
128-5730B 2

Shrnutí obsahu

Strany 1 - Model APS-255

128-5730B1 of 7Model APS-255Installation ManualNote : When both Passive Arming and Voltage Sensing are selected, you must hardwire the driver’s door p

Strany 2 - 128-5730B

128-5730B2 of 7Page 2Eight Press and release the valet switch 2 chirps = horn chirp output 16mSPress transmitter Lock button to change 3 chirps = horn

Strany 3

128-5730B3 of 7Page 3Shock Sensor :Select a solid mounting surface for the shock sensor on the firewall inside the passenger compartment, and mountthe

Strany 4

128-5730B4 of 7Page 4WARNING : Do not use the purple wire if the vehicle has ground output type door switches.( see Brown Wire ).Orange Wire : 300 mA

Strany 5

128-5730B5 of 7Page 5was issued. This is used for second step unlock or all doors unlock in a two step circuit. In this arrangement, Redis used to c

Strany 6

128-5730B6 of 7time after disarming. Because the vehicle you are working on requires a positive pulse from the factory door lockswitch to the factory

Strany 7